Disbudding Goats

Disbudding, a procedure for preventing the growth of horns, is one of the hardest things we have to do with (to) our goats but we highly recommend it unless there is a very, VERY good reason NOT to do it. In our case, we are raising hand-reared, friendly dairy goats who we enjoy as much for their interactions with us as for their productivity. That means we're around them a lot and the risk of an accidental poke with a horn is just too great to ignore.

For disbudding we use a specially-made electric hot iron tool which is applied to the horn "buds" when they are only a few days old. We are still learning about the best and most effective, and humane way to do the procedure but have found that waiting until the kid is too old is much more likely to produce "scurs", which are unwanted and possibly dangerous (to the goat) partial horns. It's time to disbud when the horn buds are able to be felt easily. With Nubians, this can be when the kid is one week to three weeks old. Swiss breeds of goats can be done earlier.

I say in the sub-title for this page that it is a "difficult" procedure. Well it is, but not from a skill or technical standpoint. It is, with the proper equipment, a straight forward and fairly simple task. The difficulties are more in our having to cope, personally, with taking the poor few-days-old critters and having to put them through it. THEY seem to have a much easier time of it then we often do.

We also usually do our tattooing of the kids at the same time as disbudding so here is a picture series of our disbudding/tattooing process.


1	About 15 minutes before starting, we plug in the disbudding iron to make sure it has a chance to fully heat. Being on solar power, we run the generator for disbudding as we find it gives better power to the iron. In preparation for the tattooing, we clean the kid's ears well with a cotton ball and rubbing alcohol. It's amazing how dirty a 2-week old ear can be! Here, our "volunteer", Brass is lowered into the disbudding box. His head is placed in the contoured support, we make sure his ears are out of the way and we secure the lid.

2	Secure in the disbudding box, Kathryn holds Brass's ears back and out of the way as I apply the extremely hot iron tip to the first horn bud. Rotating the tip around and back I continue with firm pressure to ensure good contact for about 7 seconds. There's a lot of smelly smoke from the hair singeing.

3	We repeat the process on the other horn bud.

4	Kathryn snips off the horn bud with her hoof-trimming shears and we examine the job closely to make sure we have burned fully around the whole perimeter of the bud and have gone deep enough overall. The burned ring should be a deep copper color or white. A white ring means the burn has reached the skull. We burn to a white ring when doing bucklings since they tend to grow scurs more easily.

5	I reapply the iron where and as necessary. We really want to do a good job right now and do not want to risk having to bring little Brass back in a few weeks to re-do the job if we were not thorough enough. I will also take the side of the iron and burn a bit on the center of each bud.

6	As soon as we are satisfied we have done a good job, Kathryn immediately sprays each bud with our dairy aerosol teat disinfectant (Fight Bac). The spray is very cold coming out of the can and helps cool the site and the disinfectant properties should help stave off infections.

7	We tattoo all of our registered goats in their ears. One ear gets our herd identifier and the other gets a code with the kid's birth year and birth order on the Ranch. We use green tattoo ink and a special set of tattoo pliers into which the individual alpha-numeric tattoo are arranged

8	Despite my lengthy explanation, the whole process of disbudding and tattooing takes less than a minute. Here, moments after the procedure, Brass and his friends are enthusiastically slurping up lunch, none the worse for wear. He will soon run off and be bashing heads with his buddies while we try not to cringe at the sight.